Friday, March 10, 2023

- HONDA HS OWNER'S MANUAL Pdf Download | ManualsLib

Looking for:

Honda hs828 snowblower service manual download -  













































     


Honda hs828 snowblower service manual download -



  Ray Ralph, President R.    

 

Honda HS HS HS HS HS Snowblower Shop Manual.



   

Table Of Contents. Quick Links. Table of Contents. Previous Page. Next Page. Honda HS Owner's Manual 81 pages. Honda HS Owner's Manual 54 pages.

Honda power equipment snowblowers owner's manual 41 pages. HS informa- result service if requires before your Page 4: Safety 1. Page 5 To ensure safe operation Always make a pre-operation the engine. Inspect the snowblower correct any malfunction operating the snowblower, Page 6 Adjust snow discharge bystanderds, windows, clear of the snow discharge Children and pets must avoid injury from flying debris and contact To avoid overturning, snowblower while operating to remove snow from roofs.

The snowblower slopes if left unattended, Know how to stop the snowblower tion of all controls. Page 7 Gasoline is extremely tions. Do not smoke or allow flames or sparks where the snowblower refueled or where with the engine stopped. The muffler becomes while Frame serial number: Engine serial number: GC 2. Page 9: Controls 3. Chute crank Use the chute crank to turn the snow discharge To throw snow to the left To throw snow to the right the amount of fuel in tlie tank. Page 13 Drive clutch lever and auger clutch Use these controls drive mechanism.

NOTE: When both levers are squeezed, auger clutch lever down. Releasing the drive clutch lever then unlocks and releases the auger clutch Roth levers squeezed lever to engage the snow blowing Page 14 Skid plate, Scraper Adjust the skid plates for the auger ground clearance snow removal conditions.

To prevent OFF position and disconnect 1. Place the snowblower pedal in the middle position. Move the skid plates up or down to obtain the desired auger ground clearance.

Page 15 Foot pedal Use the pedal for adjusting to the tracks. Hold the handles and step on the pedal. Raise or lower the machine pedal. Page Pre-Operation Check 4. Fuel Check the fuel gauge, and refill the tank if the fuel level is low. Refuel carefully to avoid overfilling filler neck. Use extreme Refuel in a well-ventilated allow flames or sparks in the area where the engine is refueled or where gasoline Page 18 Fuel Recommendation Use gasoline with a pump octane We recommend unleaded fuel because it produces fewer engine and spark plug deposits and extends Never use stale or contaminated getting dirt or water in the fuel tank.

Page 19 Engine oil Inspection: With the snowthrower the dipstick clean. Insert the dipstick it in. Remove the dipstick If the level is low, fill to the top of the oil filler neck with the recommended oil. It is normal for the fluid level to rise above the UPPER level mark when snowblower operation When checking the level of cold fluid, below room temperature, the temperature chart for appropriate At temperatures Page 21 Auger and blower bolts Check the auger and blower for loose or broken bolts.

If broken, replace them with new ones page Check all bolts, nuts and other fasteners 2. Check each part for operation. Page Starting The Engine 5. Exhaust cdntains poisonous carbon monoxide gas; exposure can cause loss of con- sciousness and may lead to death. Page 23 3. Page 24 5. Connect your power cord to the switch power cord to a properly -0,:. To minimize the possibility always use a 3-conductor than 15 amps.

Also, be sure that the outlet Do not connect and disconnect Be sure to hold the plug when electrical outlet or switch Page 25 7. Push the starter button until the engine starts. After the engine starts, disconnect the power cord from the electrical outlet first, and then from the switch box. Page 26 9. After starting the engine, allow it to run for a few seconds to warm it up to operating temperature.

As the engine stabilizes, gradually move the throttle lever to the SLOW position. Page 27 6. Start the engine according 2. Move the throttle Release the auger clutch desired drive speed. NOTE: Low speed is recommended snow. Adjust the throwing guide.

Page 28 6. Squeeze the auger clutch The machine will clear snow when you squeeze the auger clutch lever. Squeeze the drive clutch If the transmission the shift lever p. Page 29 To move from one place to another, or to change direction, use the drive clutch lever only.

Release both the drive clutch lever and auger clutch lever once, then squeeze the drive clutch lever. Release the clutch levers to stop clearing and moving.

Page 30 Clearing Snow For best efficiency, clear snow before it melts, refreezes and hardens. Do not reduce engine speed while clearing snow. Operating tips for clearing hard or deep snow: Reduce forward speed. If that is not sufficient, clear snow with a back and forth motion. Clear a narrower swath. Page 31 Adjust snow bystanders, windows, of the snow discharge If the snow discharge a wooden stick to unclog Never put your hand into the snow discharge running; serious personal To move from one place to another, drive clutch lever.

To restart engine, position. Release the auger and drive clutch levers. Page 33 3. Turn the engine switch 5. Turn the fuel valve to the OFF position. Page Maintenance Periodic inspection and maintenance your HS Snowblower Inspect or service as described Shut off the engine before performing disconnect the spark plug wire from the plug so that the engine cannot be started.

If the engine must run, make sure the area is well ventilated. See the Honda Shop 31 For professional commercial more frequent inspection and replacement by an authorized Honda Manual. Page 37 Engine oil change Drain the oil while the engine is still warm to assure rapid and complete draining.

Place the snowblower the snowblower in the HIGH position page Remove the drain plug and filler cap, and drain the oil. Retighten plug securely. Page 38 Spark plug service Recommended spark plug: BPR5ES If the engine has been running, careful not to touch the muffler To ensure proper engine operation, ped and free of deposits. Remove the spark plug cap. Clean any dirt from around the spark plug base.

Page 39 Track-Adjustment Make sure the tracks are clean and dry before adjustment. Check track deflection wheels. When correctly 1. Page 40 Shear bolt replacement 1.

Place the snow blower on a firm, level surface. Turn the engine switch 3. Clean the auger and blower of snow, ice or any other foreign particles. Check the entire snow clearing mechanism. Page Transporting 9.

Loading the snowblower level surface. Use a loading ramp that is strong weight of the snowblower Weight of snowblower: 3.



at

No comments:

Post a Comment

Subscribe to: Post Comments (Atom)